1000m Hydrostatic Test Equipment, Simulated Submarine Environment
Equipment
Equipment composition:
The ocean depth simulation test chamber is primarily composed of a
304 stainless steel outer casing, a touch screen control system, a
pressure controller, safety valves, and other components.
- Outer Casing and Tank Body:
Made of 304 stainless steel, they exhibit excellent corrosion
resistance and pressure bearing capabilities.
Equipped with a touch screen control system, it facilitates users
in setting test parameters and monitoring the testing process.
These ensure that during the testing process, when the pressure
exceeds the set value, it can automatically release the pressure,
safeguarding the equipment and personnel's safety.
Product characteristics:
For a comprehensive assessment of diving products' ability to
withstand pressure and remain waterproof, the ocean depth
simulation testing machine is indispensable. It simulates a broad
spectrum of aquatic environments and employs advanced water
injection and pressurization methods to conduct precise tests.
1 The Machine is suitable for IPX8 waterproof test or Simulate the
deep sea test environment.
2 The tank is made of 304 stainless steel material, which can
ensure the pressure performance of the container and is not easy to
rust.
3 All electronic control components are imported from LS,
Panasonic, Omron and other brands, and the touch screen adopts a
true-color 7-inch screen.
4 The pressurization method adopts the water injection
pressurization method, the maximum test pressure can be simulated
up to 1000 meters, and the equipment is equipped with a safety
valve pressure relief valve (mechanical).
5 The pressure sensor is used to detect the test pressure and has
the effect of stabilizing the pressure; if the pressure in the tank
exceeds the pressure, it will automatically open the safety valve
to drain water to relieve the pressure.
6 The control is equipped with an emergency stop operation button
(the pressure is automatically released to 0 meters after pressing
the emergency stop).
7 Support two test modes, users can choose according to test
requirements:
① Standard test: The water pressure value and test time can be
directly set, and the timing test will start when the water
pressure in the tank reaches this value; the alarm will be prompted
after the test is over.
② Programmable test: 5 groups of test modes can be set. During the
test, you only need to select a certain group of modes and press
the start button; each group of modes can be divided into 5
continuous test stages, and each stage can be set independently
time and pressure values. (In this mode, the number of loop tests
can be set)
8 Test time setting unit: minute.
9 Without a water tank, fill the tank with water after connecting
the water pipe, and then pressurize it with a booster pump.
10 Casters and foot cups are installed at the bottom of the
chassis, which is convenient for users to move and fix.
11 Protective device:Leakage switch, pressure safety valve
protection, 2 mechanical pressure relief valves, manual pressure
relief switch, emergency stop button.
Technical parameter:
| Item | Specification |
| External dimensions | W1070×D750×H1550mm |
| Inner size | Φ400×H500mm |
| Wall thickness of the Tank | 12mm |
| Tank material | 304 stainless steel material |
| Flange thickness | 40mm |
| Flange material | 304 stainless steel material |
| Equipment weight | About 340KG |
| Pressure control mode | Automatic adjustment |
| Pressure error value | ±0.02 Mpa |
| Pressure display accuracy | 0.001Mpa |
| Test water depth | 0-500m |
| Pressure adjustment range | 0-5.0Mpa |
| Exhaust pressure of the safety valve | 5.1Mpa |
| Test time | 0-999 min |
| Power supply | 220V/50HZ |
| Rated power | 100w |
Installation and use conditions:
1 Site of installation:Recommended installation position dimensions
≥ W1500× D1200× H2000mm；The ground load-bearing capacity is not
less than 800kg/㎡.
2 Power supply:220V / 50HZ(This is negotiable and adapted to
customer conditions),and the length of the power cable is 2.5 m.
3 Water source requirement:The supplier delivers 6 meters water
pipe (specification DN15), and the user needs to ensure that the
water source is within this range (if it needs to be extended,
please explain in advance).
4 Drainage requirement:Users should make drainage channels in the
site in advance.
5 Air source requirements: Users should provide their own air
compressor, and the output pressure should be stable at 0.6-0.8Mpa.
Notice:
Due to the technical upgrade, some technical parameters do not
conform to the actual machine, please forgive us without further
notice.
Product detail photos:
top of the jar jar - uncover
Tags: Marine environment simulation test machine , Deep water environment
simulation test machine , Water pressure environment test equipment
